Lancom Systems LS61465 Technické informace Strana 84
- Strana / 244
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
LANCOM ES-2126+ und LANCOM ES-2126P
쮿 Chapter 4: Operation of Web- based Management
83
EN
ration is to make the port quickly get back to act as an RSTP port. Click
<M Check> button to send a RSTP BPDU from the port you specified.
4.13 Trunking Configuration
The Port Trunking Configuration is used to configure the settings of Link
Aggregation. You can bundle more than one port with the same speed, full
duplex and the same MAC to be a single logical port, thus the logical port
aggregates the bandwidth of these ports. This means you can apply your cur-
rent Ethernet equipments to build the bandwidth aggregation. For example,
if there are three Fast Ethernet ports aggregated in a logical port, then this
logical port has bandwidth three times as high as a single Fast Ethernet port
has.
The switch supports two kinds of port trunking methods:
쐃 LACP:
Ports using Link Aggregation Control Protocol (according to IEEE 802.3ad
specification) as their trunking method can choose their unique LACP
GroupID (1~3) to form a logic “trunked port”. The benefit of using LACP
is that a port makes an agreement with its peer port before it becomes a
ready member of a “trunk group” (also called aggregator). LACP is safer
than the other trunking method - static trunk.
- LANCOM ES-2126+ 1
- LANCOM ES-2126P 1
- 쮿 Preface 4
- Information symbols 5
- Contents 6
- 쮿 Contents 7
- 1Introduction 10
- ES-2126+ 11
- 쮿 Chapter 1: Introduction 11
- Onyl for LANCOM 11
- LANCOM ES 13
- 2 Installation 15
- 쮿 Chapter 2: Installation 16
- 2.5 Software installation 20
- 3.1 Configuration options 22
- 3.2.1 Save/Restore 26
- 3.2.2 Config file 27
- 3.3.1 Ethernet port status 28
- 3.3.2 Port PoE status 29
- PoE class Use Power range 30
- 4.2 System 34
- 4.2.2 IP Configuration 35
- 4.2.3 Time Configuration 37
- 4.2.4 Account Configuration 40
- 4.2.5 Management Security 41
- 4.2.6 Virtual Stack 44
- 4.2.7 System Log 45
- 4.3 Port 46
- 4.3.2 Port Status 48
- 4.3.3 Simple Counter 51
- 4.3.4 Detail Counter 52
- 4.5 Loop Detection 57
- 4.6 SNMP Configuration 57
- 4.7 DHCP Boot 59
- 4.8 IGMP Snooping 60
- 4.9 VLAN 63
- - “ and “_” characters 65
- 4.9.3 PVID 67
- 4.10 MAC Table 69
- 4.11 GVRP Configuration 73
- 4.12 STP Configuration 78
- 4.12.2 STP Configuration 80
- 4.12.3 STP Port Configuration 81
- 4.13 Trunking Configuration 84
- 4.14 802.1x Configuration 89
- 4.15 TACACS+ 98
- AAA-SERVER 99
- 4.16 Alarm Configuration 103
- 4.16.2 E-Mail 104
- 4.17 Security 105
- Function name: 106
- 4.20 Diagnostics 119
- 4.20.2 Loopback 120
- 4.20.3 Ping 121
- 4.20.4 Watchdog 121
- 4.21 TFTP Server 122
- 4.22 Log 123
- 4.23 Firmware Upgrade 124
- 4.24 Reboot 125
- 4.25 Logout 126
- 5 Operation of CLI Management 127
- 5.2 Commands of CLI 128
- 5.2.1 Global Commands of CLI 129
- 5.2.2 Local Commands of CLI 135
- 6 Appendix 242
- 6.2 Connector wiring 244
Ryobi P300 manuals
Owner’s manuals and user’s guides for Tools Ryobi P300.
We providing 1 pdf manuals Ryobi P300 for download free by document types: User Manual
Komentáře k této Příručce